Encoder's output type, output circuit and wave

Output signal type	Coder	Output circuit			Wave
Open collector output	C				When resister connected between output and external high level, output wave is the same as push-pull output C2=PNP open collector C=NPN open collector
Push-pull	F
Voltage	E
Line drive output	D
	L
	P
	M
	H
UVW output for detecting AC motor	AC

Encoder electrical parameters

Model	Output type	Power supply(V)	Current Consumption(MA)	Output voltage		Injection Current(MA)	Mim.load Impedance(Ω)	Rise/fall time(VS)	Max.response
				VH	VL
05C	Open collector	5±0.25	≤100	-	-	≤30	-	≤1	0~200
05E	Voltage	5±0.25	≤100	≥3.5	≤0.5	-	-	≤1	0~200
05F	Push-pull	5±0.25	≤100	≥3.5	≤0.5	-	-	≤1	0~200
05L	Line driver	5±0.25	≤100	≥2.5	≤0.5	-	-	≤0.2	0~200
05H	Line driver	5±0.25	≤100	≥2.5	≤0.5	-	-	≤0.2	0~200
05D	Line driver	5±0.25	≤100	≥2.5	≤0.5	-	-	≤0.2	0~200
05P	Line driver	5±0.25	≤100	≥2.5	≤0.5	-	-	≤0.2	0~200
12C	Open collector	12±1.2	≤100	-	-	≤30	-	≤1	0~200
12E	Voltage	12±1.2	≤100	≥8.0	≤0.5		-	≤1	0~200
12F	Push-pull	12±1.2	≤100	≥8.0	≤0.5		-	≤1	0~200
15C	Open collector	15±1.5	≤100			≤30	-	≤1	0~200
15E	Voltage	15±1.5	≤100	≥10.0	≤0.5		-	≤1	0~200
15F	Push-pull	15±1.5	≤100	≥10.0	≤0.5	-	≥500	≤1	0~200
24C	Open collector	24±2	≤150			≤30	-	≤2	0~200
24E	Voltage	24±2	≤150	≥3.5	≤0.5	-	-	≤2	0~200
24F	Push-pull	24±2	≤150	≥20.0	≤0.5		≥500	≤2	0~200
24M	Line driver	24±2	≤150	≥18.0	≤0.5	-	-	≤0.2	0~200

Common plug used for encoder

Code	Icon	Outline drawing
P
Y
J

Matters needing attention of the encoder for installation and use

Mechanism reated
The connection between encoder and the users output shaft should be used in soft connections , avoid the use of rigid connections.
Please note that the axil loading of permission should not exceed its loading limit.
Please don't exceed the limit of its electrical speed, such as, when it exceeds the speed of its permission, the electrical signal may be lost.
The installation of encoder should be lightly fitted into the shaft sleeve, and strictly forbid hitting by hammer, percussion and crashing, in order to avoid damaging shaft and perspex disk.

Electric related
The output cable of encoder and power cable can not be fixed together of putted in same tube. The output cable should also be far from the switchboard to avoid disturbing. The cable should be shielded.
Careful check should be taken before starting the machine, the product instruction should be matched with the encoder model, wire connection should be correct, wrong connection will damage the internal circuit
Signal degradation factor should be considered when taking a long distance transmission. The output mode should be with ow outpur resistance and strong anti-disturbing capacity.
The transmission distance for pulse signal is related with the following factors: frequency, output circuit, input circuit, transmission cable and trandmitting frequency.

Environmet related
The encoder is a precision apparatus, when use it, it should be far away from vibration source.
The encoder is not designed with sealed structure, prevent water or oil etc. Splashing on it. Use a protecthood if necessary.
The environmental temperature and humidity should be in the operation range.
Note: performance and service life of encoder will be affected seriously by improper.